A cake angled spatula is a decorating tool whose blade sits at an angle to the handle, letting the user work across a cake surface while keeping the hand above the working area. For wholesale buyers, the sourcing decision is rarely just “angled versus straight.” It is a question of blade geometry, component reference, listed dimensions, handle material, order unit and sample approval. This guide walks through the publicly listed Juneshing PP-handle options and sets out the checks to complete before requesting a quotation.
Answer the exact buyer intent: which angled format fits your range?
Juneshing describes an icing spatula, also called a frosting spatula or palette knife, as a tool selected by working length and blade angle. Three PP-handle families are listed in the same range, and they differ mainly in blade orientation and listed component size.
- PP Handle Angled Icing Spatulas – SP-PP02: the page describes an angled icing blade that helps the user work across a cake surface while holding the handle above the working area. The listed angled icing component SP-PP02-008 is 29.5 × 3.6 cm at 61 g.
- PP Handle Offset Icing Spatulas – SP-PP01: the page describes an offset blade format for cake-decorating buyers comparing against straight palette knives. The listed angled icing component SP-PP01-006 is 25 × 2.5 cm at 61 g.
- PP Handle Straight Icing Spatulas – SP-PP03: a straight palette-knife format. The listed straight icing component SP-PP03-004 is 35 × 3.3 cm at 119.7 g. A straight blade follows the handle line, whereas an offset blade steps below it.
All three product pages state stainless steel blades with PP handles, and all three list angled, offset or straight icing profiles alongside scraper options. If your assortment needs a single angled cake spatula shape, identify the component code rather than the family name. The category page warns that some SP-series photographs show a family of shapes rather than one fixed-piece kit, so the model reference and the picture may not describe the same contents.
Compare only current verifiable model attributes
The table below reproduces the dimensions and weights as listed on the live pages. Treat them as starting points for a drawing request, not as final approved specifications.
| Model reference | Tool | Listed size | Listed weight |
|---|---|---|---|
| SP-PP01-006 | Angled icing spatula | 25 × 2.5 cm | 61 g |
| SP-PP01-019 | Spatula scraper | 24.3 × 10 cm | 118.2 g |
| SP-PP01-021 | Fish spatula scraper | 28.4 × 8.3 cm | 79 g |
| SP-PP02-008 | Angled icing spatula | 29.5 × 3.6 cm | 61 g |
| SP-PP03-004 | Straight icing spatula | 35 × 3.3 cm | 119.7 g |
| SP-PP03-017 | Spatula scraper | 33.3 × 7.7 cm | 197.4 g |
Two open questions should be resolved in writing for whichever reference you select. First, both the SP-PP01 and SP-PP03 pages note that listed dimensions may refer to either the blade or the whole tool, and both ask buyers to confirm both measurements and request a dimensioned drawing showing usable blade length, overall length and handle dimensions. Second, listed weights are per component reference; they are not a carton weight or a packed weight.
Compare the PP Handle Angled Icing Spatulas SP-PP02 with the PP Handle Offset Icing Spatulas SP-PP01 when the working angle is the deciding factor, and use the PP Handle Straight Icing Spatulas SP-PP03 page when a straight blade is the alternative under review. The full Griddle & Icing Spatulas category shows the wider assortment, including wood-handle and set options, so you can confirm whether a single angled component or a coordinated set better fits the listing.
Run a cake angled spatula sample inspection checklist
Samples are the point where a component reference becomes a physical product. Build the checklist around what the source pages actually promise, and leave no field assumed.
- Match the component code. Confirm the sample label carries the exact reference you intend to order, such as SP-PP02-008, rather than only the family name SP-PP02.
- Verify the drawing against the physical piece. Measure usable blade length, overall length and handle dimensions separately, and compare them with the approved dimensioned drawing.
- Confirm material and finish as listed. The pages state stainless steel blades with PP handles. Check that the sample reflects that combination and that the finish matches the approved artwork.
- Check the blade angle in the hand. Compare the angled sample against the offset and straight alternatives using your intended cake-decorating task, and record which shape you approve.
- Weigh the sample. Compare the physical weight with the listed reference weight so packing calculations are not based on an unverified figure.
- Review the packing list. Approve the final packing list before bulk production, and confirm the order unit, because a listed quantity may be per tool or per set.
- Retain the approved sample. Keep a signed reference sample and drawing together so later production can be compared against the same baseline.
Sample and quotation checks before you commit
The listed commercial terms are consistent across the three PP-handle pages, but each page adds a confirmation caveat that belongs in your quotation request.
- Minimum order: the pages list 1,000 pcs. Ask the sales team to confirm whether that quantity is measured per individual tool or per complete set.
- Production lead time: the pages list 35–45 days. Confirm the current schedule for your exact configuration.
- Logo and custom packaging: the pages list a threshold of 2,000 pieces for logo and custom-packaging requests. Discuss artwork position, finish and packaging layout before approving a private-label project.
- Sample cost and freight: the pages state that samples and packaging are available for discussion. Ask for the current sample cost, freight and packaging minimum for your selected configuration.
- Quotation inputs: the pages ask buyers to send the model reference, selected pieces, quantity, packing or logo requirements, destination and required delivery date, plus a reference image when choosing between blade or handle options.
- Handle families: the catalog includes both PP and wooden handle families. Confirm material, finish and available customization for the particular model and component rather than assuming they carry across a family.
One practical warning is worth repeating: a product image may show several shapes. Do not price a project from a photograph. Send a written selection list with component codes, and ask for a drawing matched to the photograph where several lengths share a model family. This keeps sampling and bulk-order comparisons consistent, and it prevents a quotation from being built on an assumed kit.
Juneshing is described as a trading and manufacturing company specializing in grill and BBQ tools and kitchenware products, mainly including spatulas and kitchen knives. For buyers assembling an icing spatula range, that means the useful first step is a defined product brief: the blade profile, the component reference, the overall length, the handle material and the packaging direction. Broader range context sits on the category page, while the three PP-handle product pages provide the model-level detail to quote against. Final terms for any order should always be confirmed for the exact component or set.