A griddle tool kit is not a single fixed product. Across the supplied Juneshing pages, the term covers multi-piece wood-handle selections and paired PP-handle turners. The buyer decision is therefore less about picking a kit name and more about approving an exact component list, then confirming that the quotation, sample and packing list all describe the same tools.
Start with the working task, then the model family
The category page frames griddle spatulas as tools selected for lifting and turning food on a flat cooking surface, while icing spatulas use palette-knife profiles for spreading and smoothing. A scraper or griddle turner serves a different task from an icing blade. That distinction should drive your first shortlist before you compare model codes.
Two useful starting points in the current range are the 5-Piece Wood Handle Griddle Spatula Set SP-W01 and the 6-Piece Wood Handle Griddle Tool Set SP-W01P. Both are described with stainless steel blades and wooden handles. If your assortment calls for PP handles instead, SP-PP05 pairs a long stainless steel turner with a slotted blade option.
Compare only what the current pages actually state
The table below uses only attributes visible on the supplied pages. Where a page lists a figure and also asks buyers to confirm it, treat the figure as a listed specification rather than a guaranteed production term.
| Model | Described selection | Handle family | Listed components shown |
|---|---|---|---|
| SP-W01 | Five-piece griddle spatula set | Wooden | Long spatula, slotted spatula, scraper spatula, scraper turner, flat scraper |
| SP-W01P | Six-piece griddle tool selection | Polished wooden | Three component references shown (SP-W01P-01 to SP-W01P-03) |
| SP-PP05 | Long turner and slotted scraper profiles | PP | Turner and slotted spatula scraper |
Two gaps deserve attention. First, the SP-W01P page describes a six-piece selection but shows only three component references, so the full composition must be confirmed before approval. Second, the SP-PP05 page gives component dimensions, while the wood-handle pages publish size and weight rows for their references. Do not assume that different models share dimensions.
What the pages list per component
- SP-W01: the page lists size and weight rows for SP-W01-01 through SP-W01-05, including a long spatula, slotted spatula, scraper spatula, scraper turner and flat scraper.
- SP-W01P: listed rows cover SP-W01P-01, SP-W01P-02 and SP-W01P-03, described as a bigger griddle spatula and two scraper references.
- SP-PP05: the listed turner is 38 x 7.5 cm and the slotted scraper is 34 x 7.6 cm, with weights given per reference.
Across the pages, the recurring instruction is to use the component reference to match listed dimensions with the selected tool, and to confirm the approved drawing and packing list before production. That is a drawing check, not a marketing claim.
Build a sample inspection checklist around the drawing
A griddle tool kit sample inspection checklist works best when it compares the physical sample against the approved component table, not against a category photo. The category page notes that some SP-series photographs show a family of shapes rather than one fixed-piece kit, so a photo alone is weak evidence of what will ship.
- Component identity. Confirm the component reference for every piece in the kit and match it to the quotation line.
- Blade profile. Check whether each piece is long, slotted, scraper-style or a broader turner, and whether that matches the intended retail pack.
- Handle family and finish. Separate wooden from PP handles and note the finish wording used for the exact model.
- Measurements. Compare usable blade length, overall length and handle dimensions against the listed figures and the approved drawing.
- Piece count wording. For SP-W01P, ask the supplier to document which components make up the six-piece selection before you sign off.
- Packaging. Approve artwork position, packaging layout and the order unit for the specific private-label project.
The category page also advises checking the cooking-surface manufacturer’s guidance before specifying metal utensils for coated cookware. Pass that guidance through your own compliance review rather than treating it as a product guarantee.
Quotation checks before you commit
The listed minimum order on the supplied product pages is 1,000 pcs, with a listed production lead time of 35-45 days and a listed threshold of 2,000 pieces for logo and custom-packaging requests. Each page repeats the same caution: confirm whether the quantity is measured per individual tool or per complete set, and confirm the current schedule.
Send a purchasing brief that includes the model reference, selected pieces, quantity, packing or logo requirements, destination and required delivery date. Adding a reference image helps when several blade or handle options share a model family. Use the griddle, icing spatula and scraper category to compare related models, and route sample and quotation questions through the contact page.
Checks that catch most mismatches
- Does the quotation name the exact component selection, not just the kit code?
- Is the order unit stated – per tool or per set?
- Are sample cost, freight, logo options and packaging MOQ quoted for your configuration?
- Has the final packing list been approved before bulk production?
The category description and product pages provide Juneshing’s stated background as a trading and manufacturing company focused on grill and BBQ tools and kitchenware. Verify all commercial terms directly in your own quotation, since listed specifications can change and the pages themselves direct buyers to confirm current terms.