A griddle spatula set is rarely a single decision. Wholesale buyers must choose blade shapes, handle materials and piece counts, then confirm the listed terms that apply to the exact model. This guide uses the live Juneshing catalog to show how three griddle spatula set models differ, and how to build a sample inspection checklist around the evidence you can actually verify.
Start With the Working Task, Not the Piece Count
The catalog describes a griddle spatula as a tool that supports food while turning or lifting it from a flat cooking surface. Long blades, broad turners and slotted profiles are selected by the food being handled. An icing spatula, by contrast, has a palette-knife profile for spreading and smoothing. Both appear in the same category, so the shared word “spatula” can hide a different job.
For a griddle program, the practical first filter is blade function. A long turner handles wide or fragile items. A slotted blade lets some liquid drain. A scraper clears a compatible preparation surface or divides dough. Buyers should write down the functions their retail pack must cover before comparing models, because the piece count alone does not tell you which functions are included.
Compare Only the Listed Model Attributes
Three current listings give enough detail for a component-level comparison. The table below uses only attributes shown on the named product pages.
| Model | Product type | Material and finish | Selection |
|---|---|---|---|
| SP-W01 | Wood handle griddle spatula set | Stainless steel blades with wooden handles | Five turning and scraping tools |
| SP-W01P | 6 piece griddle tool set | Stainless steel blades with polished wooden handles | Six griddle spatula and scraper profiles |
| SP-PP05 | Long stainless steel spatula pp handle | Stainless steel blades with PP handles | Long turner and slotted scraper profiles |
SP-W01 breaks down into five named components: a griddle long spatula listed at 37*7.3cm and 188.6g, a griddle slotted spatula at 31.4*7.3cm and 149.8g, a griddle scraper spatula at 31.4*7.3cm and 148.4g, a griddle scraper turner at 26.6*11.9cm and 158.8g, and a flat griddle scraper at 15*11.2cm and 158.8g.
SP-W01P is described as a six-piece selection, with three listed component references visible on the page: a bigger griddle spatula at 33*13 cm and 445 g, a smaller griddle scraper at 28.5*7.5cm and 243 g, and a griddle scraper at 30.5*9.5cm and 295 g. The page advises comparing SP-W01P with SP-W01 by blade width, working length, handle finish and included scraper shapes rather than treating the extra piece as the only difference.
SP-PP05 covers a different handle family. Its listed turner is 38 × 7.5 cm and 194.6 g; its slotted spatula scraper is 34 × 7.6 cm and 183.8 g. The page notes that a solid blade provides a continuous support surface while slots allow some liquid to drain, and recommends sampling the selected profile for the food and cooking surface your customers use.
Build a Sample Inspection Checklist Around the Listing
A sample inspection is most useful when each check maps to something the listing actually states. The following checklist turns the catalog text into questions for your own sample review. It is a buyer tool, not a claim about what any sample will show.
- Identity: Does the sample match the model reference and component reference you requested, for example SP-W01-04 or SP-PP05-014?
- Blade profile: Confirm the profile against the photograph and description, such as long, slotted, scraper or turner.
- Dimensions: The product pages list component sizes, and each says to confirm the approved drawing. Ask for a dimensioned drawing showing usable blade length, overall length and handle dimensions before approval.
- Handle material: Verify whether the sample uses wooden, polished wooden or PP handles, as listed for the model family you chose.
- Weight: Compare the sample against the listed component weight where one is published.
- Component set: For SP-W01 and SP-W01P, note that the page says some SP-series photographs show a family of shapes rather than one fixed-piece kit. Identify the exact component selection in writing.
- Cooking-surface guidance: The category page advises checking the cooking-surface manufacturer’s guidance before specifying metal utensils for coated cookware. Pass that check to your end customer where relevant.
Record each result as pass, fail or pending. A pending result is not a pass, and a sample that has not been dimensioned cannot close a dimension check.
Quotation and Order-Unit Checks
The three product pages each list a minimum order of 1,000 pcs and a production lead time of 35–45 days. They also ask buyers to confirm whether the quantity is measured per individual tool or per complete set, and to confirm the current production schedule. Treat those as open questions for the quotation, not settled terms.
Each of the same three pages lists a threshold of 2,000 pieces for logo and custom-packaging requests. Ask the sales team to confirm the current sample cost, freight, logo options and packaging MOQ for your selected configuration.
The category page also notes that several listed specifications state 1,000 pcs minimum orders and 35–45-day production lead times, with model-specific logo and packaging thresholds, and advises confirming current terms for the exact component or set.
What to Send With a Quotation Request
A clear brief reduces back-and-forth. Include the model reference, the selected pieces or component references, quantity, packing or logo requirements, destination and required delivery date. Add a reference image if you are choosing from several blade or handle options. If several lengths share a model family, ask for a drawing matched to the photograph so sampling and bulk-order comparisons stay consistent.
To compare the full range before you send a brief, browse the griddle, icing spatulas and scrapers category. For the five-piece wood-handle option, start with the 5-Piece Wood Handle Griddle Spatula Set SP-W01. The six-piece alternative is the 6-Piece Wood Handle Griddle Tool Set SP-W01P, and the PP-handle option is PP Handle Long and Slotted Spatulas SP-PP05.
Common Buyer Questions
Should I buy a set or a single blade shape?
The catalog says to identify the component code or reference photograph, size and quantity, then ask whether that component can be supplied individually or in a selected assortment. That is a configuration question to confirm in the quotation.
Do listed dimensions refer to the blade or the whole tool?
Confirm both measurements for the selected component, and request a dimensioned drawing before approval. The listings do not resolve this on their own.
Are wooden and PP handles both available?
The catalog includes both handle families. The material, finish and available customization must still be confirmed for the particular model and component.
In short, choose the blade functions first, compare only the published model attributes, then let a sample inspection and a written quotation close the gaps the listing leaves open.